
| Item | 02-11705 |
|---|---|
| Model | H220/WWWAA/FWS/WF/MWF |
| Series | High-pressure pump (H220) |
| Nominal model size | 1-inch |
| Actual fluid inlet / discharge size | 25 mm (1") |
| Wetted housing | Ductile iron |
| Diaphragm material | Sanitary Wil-Flex™ (Santoprene®) |
| Connection standard | NPT |
WILDEN / HIGH-PRESSURE PUMPS
02-11705 · 1-inch AODD Pump
This 1-inch WILDEN H220 air-operated double-diaphragm pump is identified by the complete ordering code below.
Complete model
H220/WWWAA/FWS/WF/MWF
NOMINAL MODEL SIZE
1-inch
CONSTRUCTION
AODD pump
ITEM
02-11705
01Configuration
| Brand / item number | WILDEN / 02-11705 |
|---|---|
| Pump series | High-pressure pump (H220) |
| Pump model code | H220 |
| Nominal model size | 1-inch |
| Actual fluid inlet size | 25 mm (1") |
| Actual fluid discharge size | 25 mm (1") |
| Construction | Bolted metal |
| Wetted housing | Ductile iron |
| Diaphragm material | Sanitary Wil-Flex™ (Santoprene®), full-stroke |
| Check ball material | Wil-Flex™ (Santoprene®) |
| Valve seat material | Mild steel |
| Connection type | Threaded |
| Connection standard | NPT |
02Operating data
| Published max. flow rate (family curve, water) | 93.9 lpm (24.8 gpm) |
|---|---|
| Maximum air supply pressure (do not exceed) | 6.9 bar (100 psig) |
| Maximum solids diameter | 6.4 mm (1/4") |
| Displacement per stroke | 0.189 L (0.05 gal), calculated at 4.8 bar (70 psig) air inlet against a 2.1 bar (30 psig) head |
| Listed suction lift | Dry 2.8 m (9.1'), wet 9.0 m (29.5') |
| Listed shipping weight | 38 kg (84 lb) ductile iron on EOM page 8; official store lists 85 lb for this item |
| Wil-Flex™ temperature limits | −40°C to 107°C (−40°F to 225°F); based on mechanical stress only |
The figures above come from WIL-11114-E-04, Section 5, page 8, under the heading “H220 METAL TPE/FULL-STROKE PTFE-FITTED.” This item uses FWS (TPE) diaphragms, so it is covered by that combined family block. The same block also lists a stainless-steel ship weight, so these are family-curve values, not laboratory results unique to this item number alone. The official store repeats the same worked example under “Performance for this item”: “To pump 30 lpm (8 gpm) against a discharge pressure head of 9.0 bar (131 psig) requires 4.1 bar (60 psig) and 51.0 Nm³/h (30 scfm) air consumption.” Flow rates on the chart were determined by pumping water. Suction-lift curves on page 9 are calibrated for pumps operating at 305 m (1,000') above sea level and are “meant to be a guide only.” The page 5 legend figure “Maximum Flow Rate: 94 lpm (25 gpm)” is a rounded series heading and is not used here as this item’s unique rating. Page 8 and page 4 also state: “Caution: Do not exceed 6.9 bar (100 psig) air supply pressure.” The H220 uses a 3:1 pressure ratio: 6.9 bar (100 psig) air inlet will develop liquid discharge pressures up to 20.7 bar (300 psig) (WIL-11114-E-04, pages 4 and 6); this is the series operating principle, not a unique rating for this item. Wil-Flex™ temperature limits are from page 4; the official store lists the same −40°F to 225°F range. “Maximum temperature limits are based on mechanical stress only.”
03Materials and connections
| Wetted housing | Ductile iron |
|---|---|
| Outer pistons | Ductile iron |
| Air chambers | Ductile iron |
| Center section | Aluminum |
| Air valve | Aluminum |
| Diaphragm material | Sanitary Wil-Flex™ (Santoprene®), full-stroke |
| Valve seat O-rings | Wil-Flex™ (Santoprene®) |
| Air inlet connection | 1/2" |
| Fluid connection type | Threaded |
| Connection standard | NPT |
Materials follow the model-code decode in WIL-11114-E-04, Section 2, page 5: W = DUCTILE IRON (wetted path, outer piston, air chambers); A = ALUMINUM (center block and air valve); FWS = SANITARY WIL-FLEX®, [SANTOPRENE® (two black dots)]; WF = WIL-FLEX® [SANTOPRENE® (three black dots)] (valve balls and valve-seat O-rings); M = MILD STEEL (valve seats). The official store listing for item 02-11705 gives the same configuration: wetted path Iron, outer pistons Iron, air side Aluminum, diaphragm Santoprene®, diaphragm design SANITARY, diaphragm stroke Full-Stroke, valve Santoprene®, valve seat Mild Steel, O-rings Santoprene®, connection NPT. FWS is a diaphragm material code; it is not a statement that the complete pump is FDA- or sanitary-certified. The official store lists FDA as false for this item. Air inlet 1/2" is from the page 8 family block.
04Recommended repair kits
| Kit type | Item number | Description |
|---|---|---|
| Air kit | 02-9992-99 | KIT, AIR, H/1"/A/M/M |
Enquiry information
Quote 02-11705 and H220/WWWAA/FWS/WF/MWF, together with quantity, fluid, operating temperature, required flow and discharge pressure. For replacement parts, include the component number and a clear pump nameplate photo.